Printable View
i bought a glass pipe from my friend yesterday its really nice. I dont think he ever cleaned it. I was cleaning it with q-tips and rubbing alcohol there was tons of resin on the q-tips. could i cut off the cotton part of the q-tip and smoke it with the rest of my resin. This is my second time actually collecting reson
i doubt thats a good idea cuz ud be smoking the cotton stuff on the q tips but im not sure
No. Just throw the q-tips away as you'll be smoking cotton.
I was also wondering myself how to get resin out of a pipe to smoke it.
First, take something sharp like a metal nail file and scratch off as much resin as u can reach. go to ur nearest headshop and ask for cotton pipe cleaners. take ur pipe and a lighter and run the fire over the place where the resin is most concentrated. Take the pipe cleaner and a try to run it into the resin. if its soft, u should come away with lots of resin on the pipe cleaner which u can scrape off and smoke. i found out after like years of smokin. u can be very creative when ur high. good luck
get your swiss army knife, find a nice pointy narrow tool on it, and scrape with that. if you have enough shit,
also, if you can remove the downstem from a bong, it's an absolute resin bank in there, but you should let dry overnight
resin is great for when you have money to buy herb, nothing to do, you wanna smoke herb so badly, but no one will pick up their stupid phone. for the times when the fiend inside comes out, get out that resin and u will be shocked at how high you get
After I would go thru the crap of TRYING to get all the resin to one spot, I would do the pipe cleaner deal after applying heat. I also clip a wire coat hanger and would make me a good scraper and scrape the glass. However that was back in time. Anymore the wife and I just Boil them out 2x a week and were done with it. Nothing like a good frosty Nug, being smoked thru a clean peice. Dont get me wrong I have smoked Plenty of Resin in my time. But it hasn't had to be like that for a while now. However I am prepared if need be.:thumbsup:
Quote:
Originally Posted by pixel
Yea that happens to me too much
resin is stinky...
it seems like the high is a lot shorter too.
boil it in water or put it into a container with some efferdent
Just put it in a pan of boiling water or what?
No no no the best way is this:
Materials:
1. get a large bowl big enoiugh to submerge your piece in.
2. Fill it with hot water
3.can with a plasitc top. ex. pringles can, coffee can
4. coffee filter
5.Paper clip
Procedure:
take your piece submerge it in the bowl of hot water. leave it there for like two minutes take it out and pour out all the water back into the bowl. there should be black resin coming out. now take the paper clip and scrape the bowl. repeat this process 3 to 5 times or untill u have a lot of black resin in the bowl of water. take the can and cut the bottom out of it so it is just a cylinder with a plasic top. now cut the center out of the plastic top. take the coffee filter and put it on the top of the can and secure it by snaping the plastic top on it. so it should be a can with a filter on one end held in place by the top. now take the device u made out of the can and place it in the sink or somewhere with drainage. pour the water in your bowl through the filter slowly. you should see the resin colecting on the filter. then un hook the filter and kinda form all the pieces of resin together making one big piece of resin. and there you go smokable resin.
http://boards.cannabis.com/recreatio...sin-guide.htmlQuote:
Originally Posted by Fore20
Cool, thanks casper and slipknot
I hate smoking resin, but hey you gotta do what you gotta do.
Quote:
Originally Posted by 1chronic
Why, I thought it gets you higher
actually, what i've found to be the best scraper is a piece of a coat hanger. go get a wire coat hanger that is not too thick and a pair of wire cutters. next cut the wire towards 1 of the ends of the long part. then cut it again 5 inches down. take that 5 inch piece of wire and make a small bend on 1 end to make a scraper hook thing which you can reach to the edge of the insides. if you use this it will be easier to scrape the resin off the tool. hope this helps.
Now after you have gotten the resin, you may notice that your fingers are stinky and black! YUCK! Here's how to get the stuff off- plain old soap and water won't cut it. Take a couple of squirts of liquid hand soap and hand sanitizer- no water. The two combined really cut the resin. When your hands look clean, rinse them under warm water. Repeat if necessary.
The resin I get from my vaporizer is sticky, so I cut it with finely powdered shake. I just rub it through a wire mesh tea strainer. It's a hassle since the strainer is small, but I don't need much. It makes the resin easier to handle and also it burns better. - Granny:hippy:
boil your bowl in water and pour the black water through a screen. smoke the resin
soak it in hot water for like 2min and scrape it with a knife.
ive actually broken my piece by scraping it when i was high. i was using a mini flathead screwdriver and applied too much pressure near the hole and it broke. sucked too cuz it was a very nice inside out bowl:mad:
Dude(s) where i live you just use a LIGHTER, heat up the bowlpiece, and then use a PAPERCLIP to SCRAPE the RESIN!!!
i olnly ever really take resin rom my downtube. Its really aqward to get to the inside of my bong because it dont unscrew, also the hot water methods are hard because its 4ft...n i dont have many 4ft bowls lol.
yeah that is all there is too it. Then use rubbing alcohol or 420 cleaner to get it shiny.Quote:
Originally Posted by bongmaster00