Activity Stream
227,828 MEMBERS
1700 ONLINE
greengrassforums On YouTube Subscribe to our Newsletter greengrassforums On Twitter greengrassforums On Facebook greengrassforums On Google+
banner1

Results 1 to 4 of 4
  1.     
    #1
    Senior Member

    DIY- How To - Carbon Filter

    Pic 1- Here are all the supplies you need for this 4" carbon scrubber.
    Bodom Children Of Reviewed by Bodom Children Of on . DIY- How To - Carbon Filter Pic 1- Here are all the supplies you need for this 4" carbon scrubber. Rating: 5

  2.   Advertisements

  3.     
    #2
    Senior Member

    DIY- How To - Carbon Filter

    First thing to build is the inner chamber.

    pic1 - supplies:
    6"-4" reducer
    4" cap
    2 - 4.5" screw fasteners
    10" length of Heavy duty chicken wire
    2 - pannyhose legs

    pic2 - Wrap the 10" length of chicken wire around the 4" end cap to form a cylinder. I used a bunch of zip ties to secure the cylinder's shape.

    Pic3 - Slide the pannyhose legs over the cylinder to act as a screen for the carbon.

    Pic4 - Secure the end cap on one end of the cylinder with one of the 4.5" screw fasteners.

    Pic5 - Secure the 6"-4" reducer to the open end of the cylinder with the other 4.5" screw fastener.

    That's it. The inner chamber is done. Set aside we'll need it in a bit.

  4.     
    #3
    Senior Member

    DIY- How To - Carbon Filter

    Next to build is the Outer Chamber.

    Pic1-Supplies
    6" cap
    2 - 6.5" screw clamps/fasteners
    12" length of Heavy duty chicken wire
    3 - pannyhose legs

    pic2 - Wrap the 12" length of chicken wire around the 6" end cap to form a cylinder. I used a bunch of zip ties to secure the cylinder's shape.

    Pic3 - Slide the pannyhose legs over the cylinder to act as a screen for the carbon.

    Pic4 - Now you should have all of these parts....almost done:thumbsup:

    Pic5- Now slide the 6" cylinder over the 6" section of the 6"-4" reducer (and the inner chamber) and secure with a 6.5" screw fastener

  5.     
    #4
    Senior Member

    DIY- How To - Carbon Filter

    Filling with Activated carbon and finishing it.

    pic1 - Without the 6" end cap on the bottom, the filter should look like this....notice this space in between the chambers....this is where the activated carbon goes.

    pic2 - I used an oil spout with the end cut off to more easily disperse the carbon into the filter.

    pic3 - Here is the filter filled with carbon.

    pic4 - Finally put the 6" end cap on the bottom and we're good to go.

    Pic5 - Here is the finally product.


    Have fun kiddies...post if you have a question:thumbsup: :smokin:

Similar Threads

  1. What Is a Carbon Filter???
    By GIjaneBRAD in forum Indoor Growing
    Replies: 2
    Last Post: 02-09-2010, 08:33 PM
  2. carbon filter or no carbon filter???
    By Dozer001 in forum Indoor Growing
    Replies: 3
    Last Post: 12-04-2009, 11:59 AM
  3. carbon filter or no carbon filter???
    By Dozer001 in forum Indoor Growing
    Replies: 0
    Last Post: 11-30-2009, 10:27 AM
  4. Carbon Filter / can fan
    By KickYoAss in forum Growroom Setup
    Replies: 6
    Last Post: 04-28-2007, 11:32 AM
  5. carbon filter set up
    By babystarbud in forum Growroom Setup
    Replies: 6
    Last Post: 08-01-2006, 01:12 PM
Amount:

Enter a message for the receiver:
BE SOCIAL
GreenGrassForums On Facebook