a new smoker in need of advice

[crazymollz56]

hey, so i just started smoking pot a few months ago and im in 9th grade but when i smoke its always with other people using their pipes. i dont know how i would get a pipe and i dont just wanna smoke joints cuz its like all the smoke comming off of them could be going into your lungs ya kno? if any one has any ideas that would be awesome! thanks

crazymollz56 Reviewed by crazymollz56 on 10-30-2004. a new smoker in need of advice hey, so i just started smoking pot a few months ago and im in 9th grade but when i smoke its always with other people using their pipes. i dont know how i would get a pipe and i dont just wanna smoke joints cuz its like all the smoke comming off of them could be going into your lungs ya kno? if any one has any ideas that would be awesome! thanks Rating: 5

[onelove4all]

get someone who is 18 to buy u a pipe or make one

check threw old post for directions and if there not on this site

check out


marihemp.com

[meek mike]

There are a few ways you can make a pipe. One way is go to a part store and buy pluming pipes and make your own. I had a metal one around your age that had to bowls at the end and a long shaft. My friends called it cock knocker. Just twist them together and add a screen and your set. Another way is more of a temp pipe that you can take a part very fast and throw away. First go to the store and get a crunch bar. Really any candy bar that has the foil wraping and not the paper heck a hersey kiss can work. Then pull out the pen you did your home work with. Take it a part placing the foil from the candy bar around the ink part. Place the foil in the pen enough to make a one hitter. Fold the rest of the foil down and add tape around it or a rubber band. Make a few small holes in the foil and you have a one hitter that also provides food for after you smoke. You can make a pipe out of anything if you want. I've used soda cans many times although I heard thats not good. Be creative. I've made a bong out of two dixie cups, tape, another pen, and the one hitter I told you about. All I had to do was add another pen on the top by the bowl and suck through it. Tape the sides and bingo bongo.

Rev. Michael T
Soldier for Christ and Cannabis

[gjayde]

build yourself a bong...

[Cas420]

ask around to see if anybody's selling their piece. you can get a used metal bowl off of some one for 5$.

[crazymollz56]

thanks those were all really helpful

[crazymollz56]

how would i build a bong?

[shogun]

Make an apple pipe, you just carve a bowl out, then bore a hole through the apple into the bowl. When you finish smoking, you have a cure for cottonmouth and the munchies.

[meek mike]

Building Your Own Bong

First off you need a pen that you can take the inerds out of easily, a milk jug of plastic bottle, a good sharp knife, and some aluminum foil or something else to make a bowl out of, and some duct tape or medical take.

1)Take the inerds out of the pen

2)Use aluminum foil to make a bowl (whatever size you want it) tape it on good with the tape

3)Cut a small hole near the bottom of the bottle and insert the pen so that is is at an angle and touches the bottom

4)apply tape liberaly to make a good seal

5)Make a choke if you like

6)Pour water into the bottle to just about 1-1 1/2 inch below the bowl

7)Pack the Bowl

8)Suck out of the mouth of the bottle and light the bowl

9)When the bottle is full of smoke ( i mean so dense you cant see through it if you tried) release the choke and suck it in deep

10)Congrats you've just built and smoked your own bong

NEXT

1)Ok first drill a hole in 1 butt cap just barely big enough for the male side of the brass fiting to fit into then screw on the thread to non-thread adapter epoxy the bowl side to ensure air tightness

2)Cut off about 2 inches of the 2 inch pvc and put the butt cap on it

3)while the epoxy dries ( this should take from 10 minutes to and hour depending on the brand) cut off anothe 2 inch peace of the 2 inch pvc and put the second butt cap on it, then take the y fiting and with 2 openings facing the ceiling put the one that faces the floor on the other side on the 2 inch peace

4)after the epoxy dries cut a peace of the 1/2 inch pvc just long enough to reach from the adaptor to about the middle of the y fiting from the 45 degree side

5)put the elbow on facing downward and cut anothe peace to reach about 1/2-1 inch from the bottom

6)now take the rest on the 2 inch pvc and cut the main tube as long as you wish (mine stands at about 3 feet total)

7)inset into the straight up hole on the y fitting

8)put the cupling on as a mouth peace

9)drill a hole about 3 inches from the y fiting as a choke

10)smoke that puppy

This pipe can be made preety much any size with a few modifications, i have an 8 inch wide one that is about 10 feet long, just added a couple of reducers to make the mouth peace right

Rev. Michael T
Soldier for Christ and Cannabis

[420aLLyEarRouNd]

when i started smokin i didnt have papers or anything but if u get creative u can get high: 1. one way is to get a toilet paper roll and cut a square hole in the top, then get a piece of tin foil and put it over the hole and push down to form a bowl head (make sure u get a big enough piece of tin foil so that theres enough room to make a bowl and tape it on to the roll, then get a tooth pick or somehitng like that and poke tiny hole in the tin foil, pack the bowl u made, put ur palm over the end ur not smokin, and ur mouth over the other one and light and enjoy