Results 1 to 10 of 23
-
08-19-2006, 01:14 AM #1OPSenior Member
Joint problem (wont stay lit)
Well last night I rolled a jay, and it wasn't hitting too well, plus it went out after every hit. So I had to unroll the joint and use my pipe instead, as you can see the papers still in my ashtray. I figured that weed wasn't broken up enough, and it was too thick to draw smoke and also wouldn't burn cause there was no flow, also I may have rolled it too tight.. Well tonight I used scissors and I thought I got it ground up pretty good, and I even unrolled is several times before sealing it to make sure it wasn't too tight. This one hits fine, but it just won't stay light. I've never had this happen to me before so I'm a little confused. The weed doesn't seem like its damp, so I don't think thats the problem, it might be, but I'm not sure.
Anyone care to give some input?Frivolous248 Reviewed by Frivolous248 on . Joint problem (wont stay lit) http://img246.imageshack.us/img246/9813/brndvk4.jpg Well last night I rolled a jay, and it wasn't hitting too well, plus it went out after every hit. So I had to unroll the joint and use my pipe instead, as you can see the papers still in my ashtray. I figured that weed wasn't broken up enough, and it was too thick to draw smoke and also wouldn't burn cause there was no flow, also I may have rolled it too tight.. Well tonight I used scissors and I thought I got it ground up pretty good, and Rating: 5
-
08-19-2006, 01:28 AM #2Senior Member
Joint problem (wont stay lit)
Even a slight bit of extra moisture will cause runs and joints that go out.If you can bend a decent sized stem and it DOESN'T snap off clean,then you still have excess moisture in the bud.
-
08-19-2006, 03:09 AM #3Senior Member
Joint problem (wont stay lit)
pack it more. that might be your problem. make sure that it is packed tight
-
08-19-2006, 03:28 AM #4Senior Member
Joint problem (wont stay lit)
I put tobacco in joints to help them burn well...it works nicely and tastes better in my opinion.
-
08-19-2006, 03:33 AM #5Senior Member
Joint problem (wont stay lit)
blah dont put baccy in your j's!! keep it pure
Take a pencil or something a bit smaller than the width and pack in the ends. You could also try letting it dry out more, or breaking the bud up finer.
I get bud that is impossible to roll joints with, doesnt work, too sticky, feels like its been dipped in maple syrup
-
08-19-2006, 03:53 AM #6Senior Member
Joint problem (wont stay lit)
tb has its place and mj has hers. personally i dont like to mix them. cant rip it as good.
-
08-19-2006, 04:19 AM #7Senior Member
Joint problem (wont stay lit)
Originally Posted by CBsDankNugs
-
08-19-2006, 05:17 AM #8Senior Member
Joint problem (wont stay lit)
well I always did it that way since everyone I know does that over here...It became a habit. I tried pure sometimes but I still like it better with baccy in it...you don't even taste it and I like the little rush nicotine adds :dance:
I guess everyone has their ways
-
08-19-2006, 05:31 AM #9Senior Member
Joint problem (wont stay lit)
Originally Posted by Frivolous248
better luck next time
-
08-19-2006, 01:41 PM #10Senior Member
Joint problem (wont stay lit)
Originally Posted by MaryjaneAndHashley
Advertisements
Similar Threads
-
my ph wont stay put
By hippygirl420 in forum HydroponicsReplies: 4Last Post: 04-10-2008, 02:02 PM -
Joint problem
By Fore20 in forum Marijuana MethodsReplies: 5Last Post: 07-21-2007, 07:21 AM -
JOINT PROBLEM-PLEASE READ
By Mr.biggs in forum Marijuana MethodsReplies: 32Last Post: 07-17-2007, 05:26 AM -
Wont stay lit
By op peat in forum ExperiencesReplies: 12Last Post: 10-21-2006, 08:53 PM -
Problem With Joint
By xkasx12 in forum Marijuana MethodsReplies: 7Last Post: 02-15-2005, 12:19 AM