That would be great to smoke but I think it would be a tad bit safer if you cooked out as much of the butane and alcohol as you could over low heat under a ventilation hood. I have made it many times before as you said, but I always cook out as much butane as possible when I do it this way.

You should try to make something we call "hempka".

I have been living out in different parts of Asia for quite some time now and learned this technique from friends who hail from a country Reagan didn't like too much.

The process is easy, but do be careful cooking down the alcohol. As long as you have a ventilation hood and you aren't smoking, it really isn't that terribly dangerous (unless you are an idiot).

I usually use about 100-150 grams of cheap powder hashish, but you could use weed or black hash too if you wanted to. Just try to get everything ground up real well beforehand if you are using weed. I think you could use black gumball hash, but it would be more of a waste than anything, this method is usually only done with powder, low-grade hashish.

Anyways, take the hash and let it dissolve in 99% medical grade alcohol (isopropyl). Although something like ethyl alcohol would work (Everclear, moonshine, etc.) it just works better if it's isopropyl, at least in my experience.

Some people let the hash sit in the alcohol for three hours, some six hours, some two weeks. I guess it really doesn't matter here too much, but the more patient you are the more THC that will dissolve into the alcohol. If you wait three hours and then cook everything down you could probably use the same shit three or four times and have a weaker batch than if you leave it in there for three days and cook it down once. Either way...(common sense)

You should like a brownish-greenish oil rise to the top and a bunch of shit (oops, I mean sediment) at the bottom of your jar or bowl or whatever you used to dissolve it in. The sediment is all the dirt, donkey shit, sand, and whatever else the hash powder has in it and I usually throw it away, but you could try soaking it again and making another batch if you are hard up for smoke!

Take some cheesecloth or filter paper and pour the hash-alcohol liquid out into a pan being careful to filter out any of the dirt or sand at the bottom of the jar. Filter as much as you can and ring out the filter manually with your hands to get that last drop of goodness.

Now under low heat on a gas or electric stove, (I prefer gas because it is easier for me to gauge how much heat the concocation is receiving) start to heat up the mixture and stir constantly. I happen to have a ventilation hood over my gas stove so I am never too concerned about blowing up. If you don't then I would recommend getting a fan, opening up windows, whatever you have to do to create a suitably ventilated area.

As you are heating the mixture, stir constantly!!! STIR CONSTANTLY! You will be able to see the vapors from the alcohol rising and boiling out of the mixture. Little by little the mixture will become thicker and thicker, kind of like making Jell-O pudding.

NOW this is VERY important. I suppose there are other ways you could do this, but the resulting chemical reaction (HEMPKA) is extremely sticky! I mean extremely sticky! I usually add about four packs of cigarette tobacoo to the mixture while it is warm and most of the alcohol is evaporated and mix together by hand. Then I take the THC infused tobacco and let it air dry on some newspaper for a couple hours.

The result, with any luck, should be a black, resinous, THC-infused, tobacco mixture that you can make shapes out of like clay. You should be able to roll it out like dough, or roll it into a block.

Make sure you let enough of the alcohol evaporate though! If you don't the smoke will have a harsh taste and smell and could potentially cause medical problems. But if you aren't any idiot, and didn't fail high school chemistry, you should be able to figure out when the alcohol evaported off and you are just burning your hempka.

Good Luck!

Any questions, let me know.
:rasta:
Binzhoubum Reviewed by Binzhoubum on . Honey Oil(the easy way) Ok here we go this is a simple recipie for hash oil I found and takes almost no time. What you need: A power drill One bit tiny tiny bit Another bit slightly bigger(enough to relieve pressure from a butane can) Can of Butane Your pot(2-3oz is good amount) A 3" long 3/4" wide pvc pipe 2 caps for your pvc pipe Rating: 5