vaporizer

[sean140]

does anybody know of any links on making a vaporizer out of a light bulb?:rasta:

sean140 Reviewed by sean140 on 04-27-2006. vaporizer does anybody know of any links on making a vaporizer out of a light bulb?:rasta: Rating: 5

[tokinggreg]

http://www.waytoomany.com/vids/weed/homemadevap.php

it doesn't get much better than that...

have fun!

[zalami128]

im fucking faded off of my light bulb vap right now... works great

[WaKeNvAp]

yeah i had to make one as soon as tokin posted that. capri sun refreshers come in a bottle that has a top that spins on airtight with no tape

[sean140]

when i was watching that movie y did he put salt in and shake it around

[Radio Caca]

I just tried this and it didn't work, like nothing happened. To those who got this to work: how long did you hold the lighter under the weed. Also are you supposed to hold your finger over the choke and the end of the pen while the bulb fills up with smoke? And if you are do your fingers get hot, cause I was pretty high and thought it might get hot so I wore my dad's work cloves and held them shut hahaha

And to sean140, I know this thread is old but the salt takes the white shit off the bulb. Or you could just use a "white light" light bulb like I did and skip that step...

[kaneda7777]

ok its actually pretty hard to make out what the hell they are doing can does anyone have a step by step guide on how to do this please

peace

[Radio Caca]

Ok, the idea, I think, is to hollow out a light bulb and basically stick a pen on the end to inhale it. So what I did was literally saw the black part of the light bulb off with a hand saw. Then I ripped the actual light bulb part out so that it was all glass and metal. Then depending on what light bulb you use, dump salt in and mix it around to get the white stuff off. Then put two holes in a bottle cap, one for the choke and one for the plastic part of a pen. Then cut the top of the bottle off and make cuts down it so that when you tape it the plastic is flush with the bulb. So then tape it up really good, below the cap part so you can unscrew it and reuse it.

Then dump, light, and inhale. Keep in my mind this is all coming from the guy who couldn't get it to work though, so if someone wants to correct me be my guest...

[mastahaze]

when i was watching that movie y did he put salt in and shake it around

he put the salt in to get the white stuff of the edges

i madfe one last weekend, and it works great, herse mine http://i31.photobucket.com/albums/c3...0906_1224a.jpg

[bayareapothead5]

OK, HERES THE STEPS!
1. get a round lightbulb.
2. get a hand saw, with small ridges, not large ones, and cut off the end black part of the lightbulb.
3. rip off the silver metal part at end of lightbulb
4. rip out the metal stuff insidde the lightbulb.
5. there is some glass that might be in your way to take out the metal inards, just break the little pieces of glass off.
6. get a soda bottle cap, make 1 small hole in top, and 1 just enough to fit a straw in it.
7. screw the bottle cap onto the lightbulb where the silver, metal piece used to be.
8. place straw in the whole.
9. put weed in the lightbulb(take off cap, then replace after weed is in)
10. put mouth on 1 end of the straw and the other end is in the lightbulb.
11. hold lighter to glass where the weed is.
12 suck in slowly ass you see the smoke going up from the weed.
13. get HIGH AS FUCK!
14.(optional) take already vaporized wee from step 13, and pack into a pipe.smoke that shit and get high again!
15.clean outside of vaporizer with a kleenex, wet preferably.
16.make a new vape every 25 times of use, they where out and become VERY easy to shatter.