Results 1 to 8 of 8
-
04-08-2008, 09:35 PM #1OPJunior Member
bong question
I have this bong I got from a friend for free. Only deal is, I didn't get a slider with it. So I rigged up some paper and a chillum and went to town. Recently I've been looking into buying a new slider but notice all the measurements and such on the ads. What do I need to measure on my bong or how do I tell what size of a slider I need?
tengrand Reviewed by tengrand on . bong question I have this bong I got from a friend for free. Only deal is, I didn't get a slider with it. So I rigged up some paper and a chillum and went to town. Recently I've been looking into buying a new slider but notice all the measurements and such on the ads. What do I need to measure on my bong or how do I tell what size of a slider I need? Rating: 5
-
04-08-2008, 11:46 PM #2Senior Member
bong question
Measure the downpipe, the slide should fit into that.
Depending on the style of the bong it will be glass on glass, or it will utilize a rubber gasket.You\'ve got to be the change you want to see in the world, so I do what I want. I cannot force others to accept me, I can only lead by example and be righteous and stick to my convictions with integrity in hopes they\'ll dig what I\'m about and join in too.
-
04-09-2008, 03:12 AM #3Member
bong question
Slider? I've been smoking out of bongs for a good 5 or 6 years now, what the hell is a slider? I've never needed one.. all I got is my bong and my bowl and I've been fine every since.
-
04-09-2008, 03:50 AM #4Senior Member
bong question
Originally Posted by samostalan
You\'ve got to be the change you want to see in the world, so I do what I want. I cannot force others to accept me, I can only lead by example and be righteous and stick to my convictions with integrity in hopes they\'ll dig what I\'m about and join in too.
-
04-09-2008, 05:22 AM #5OPJunior Member
bong question
Do I need to measure the diameter of the downpipe or just the length of it? Reason being, all the bongs I've smoked have been smaller than this one. Much appreciate the help also.
-
04-09-2008, 10:22 AM #6Member
bong question
Originally Posted by maxsuperdanks
-
04-09-2008, 02:09 PM #7Senior Member
bong question
Originally Posted by tengrand
As long as the downpipe goes into the bong water the slide should be fine any length.You\'ve got to be the change you want to see in the world, so I do what I want. I cannot force others to accept me, I can only lead by example and be righteous and stick to my convictions with integrity in hopes they\'ll dig what I\'m about and join in too.
-
04-09-2008, 02:22 PM #8Senior Member
bong question
You need to do 2 measurements:
-Interior diameter of the downstem. There are 2 standard sizes of replacement sliders, not including glass-on-glass. You need to know this number.
-Maximum length that your new slider can be without making contact with the side of the bong, etc. This is approximately the length of the downstem, but you shoudl check. Measure by sticking a chopstick into the bong as far as it will go before making contact, then draw it back about an inch and pinch it right where it enters the hole. That's the longest possible slider your bong will safely accept.
Advertisements
Similar Threads
-
question about a bong
By jfoster in forum Marijuana MethodsReplies: 5Last Post: 07-14-2007, 11:46 PM -
bong question
By Dmo18 in forum Marijuana MethodsReplies: 6Last Post: 11-09-2006, 01:16 AM -
Bong question
By Mary Jane x3 in forum Marijuana MethodsReplies: 9Last Post: 02-25-2006, 12:32 AM -
Bong Question for bong experts.
By RIP ODB in forum GreenGrassForums LoungeReplies: 14Last Post: 04-02-2005, 08:53 PM -
question about bong
By CCR in forum Marijuana MethodsReplies: 4Last Post: 12-15-2004, 03:35 AM