Results 151 to 160 of 232
-
02-07-2008, 10:53 PM #151OPSenior Member
Clone Log - Cloning with Pics using Master Kush mom...
To get the little clones out, just grab them gently by their stem and coax them out of the vinyl tubing. When I do it I take off the lid and guide the roots thru the bottom side opening while pulling them from the top.
Sounds a lot more difficult than it is in reality. Sometimes a little root will get damaged but at this stage they are growing roots regularly and if one gets damaged no biggie. Just remove the damage and it will be replaced in no time with no real stress on the clone.
Check out this post to see some pics of clones further along. It is good reading too. I used many of his concepts so far...
-
02-08-2008, 02:59 AM #152Senior Member
Clone Log - Cloning with Pics using Master Kush mom...
1. Transpiration is limited by an application of AntiStress coating which forms a semi-permeable membrane around the leaf and stem surfaces.
2. The protective coating only partially blocks the stomata...
Sounds a lot like an anti wilt to me, but if they insist it's not, maybe it isn't. I was under the impression it would limit transpiration, and then I read the above and my suspicions were confirmed. I was always under the impression that you wanted as much transpiration as possible, or at least I was pretty sure blocking stomata is bad. Isn't an anti-wilt or semipermeable membrane a temporary fix? Along with dealing with spider mites once per week instead of just fixing the problem?
About the clone tubes, normally you want a slit down the length of the tube. That way you can just pry the tube apart, but still use it next time. This is one reason I recommended working the professional replacement neoprene inserts into your design.
Horticulture Source Popup - NEOPRENE INSERTS 3" FOR AMERICAN AG POWER CLONERS
I think they make em 1.5" to 6" dia.
-
02-08-2008, 03:11 AM #153Senior Member
Clone Log - Cloning with Pics using Master Kush mom...
PS. my first tubes had a slit in them, and I never used the slit. They always seem to slide out the top just fine, unless you let them stay in the cloner extra long. Like MVP says, occasionally a root will break off, but that still leaves the other 10 or 12.
-
02-10-2008, 06:25 PM #154Senior Member
Clone Log - Cloning with Pics using Master Kush mom...
ok, if this is the official cloning log as previously stated, without further delay,,,,,
here is the cloner I made up for WH.
1st an admission,,,or 2.
this took longer than I anticipated due to some circumstances beyond my immediate control.
aaaaaaaaaand,,,,
due to my notorious OCD and some mania thorwn in for good measure, the first version I was assembling was,,,well, ridiculously over-engineered.
Once I took a few breaths and realized I was creating the largest cloner in the history of cloning, I scaled back.
i had nearly all the parts here n there in my collection of 'stuff'.
Parts-
2x rubbermaid ruffneck 3gal tubs. (2 because i didnt really go for the foil tape thing, so, the walls are doubled to protect the roots from light.)
1/2 inch PVC tubing, because i had it on hand from a previous project.(cut to 2.5 inch)
1/2 PVC caps, for the ports not in use
2X 10 inch airstones
dual port pump
vinyl sink mat used to weight the airstones onto the bottom, cut out a few of the slots to weave the airstones thru, then cut in half and zip-tied to fit the tub properly.
lil clips and zip-ties to hold pump on outer tub.
and lastly, a fancy-schmancy on/off switch, just cause i had it and liked the idea of an on/off switch.
i cut the pipe holes tite, so there was no need for glue and also affords adjustability is desired.
thats it. hope you like it.
email me backchannel and we'll get this puppy out to ya:thumbsup:
oh crap, forgot to take a pic w-dome on, batteries died, ill get some and pic that too.
-
02-10-2008, 06:59 PM #155Senior Member
Clone Log - Cloning with Pics using Master Kush mom...
Rock That is GORGEOUS!!!!
Thank you so much....I'm really touched by all the work put in there!! I'll e-mail you....
-
02-10-2008, 09:03 PM #156Senior Member
Clone Log - Cloning with Pics using Master Kush mom...
got your email.
no worries, my pleasure
here's a pic w-dome.
overall dimensions w dome on.
16L x 10.5W x 14H
oh, btw, it looks like the magic number is 2 gals to bring water up to the best splash level.
-
02-10-2008, 11:27 PM #157Senior Member
Clone Log - Cloning with Pics using Master Kush mom...
Rock I tried to rep you for that but can't ......must have recently. MVP and/or Opie.....do you guys turn off your bubblers for awhile and if so.....what kind of times do you run them on? Seems as though my stems are getting too wet.
Gotta get all this sorted out before I get my new COOL cloner from Rock....::thumbsup:
-
02-11-2008, 12:35 AM #158Senior Member
Clone Log - Cloning with Pics using Master Kush mom...
Rock,
Real nice. Those end caps on the PVC is a nice touch. So is the sink mat. Good idea for a troublesome problem. A-, only due to the pump being too small, and the wrong kind of air stones. Of course that's just IMO, which only counts if I'm the one grading. 2 gal of water sounds about exactly right for a 3 gal container. Sorry, I couldn't rep you either.
WH,
I've always said that you want to keep the roots as dry as possible, while still suppling the necessary moisture. This is true not only during rooting, but in all phases IMO. Giving the plants air with their moisture makes them grow up to be jolly green giants. Here's what I shoot for during cloning: If possible, adjust the air pump to a lower setting and keep it on 24/7 until all plants show root buds (2-6 days). From then on the pump cycle should be decided through experimentation, but I try to use something like 5 minutes on and 30 minutes off, with the pump set to the highest setting. This is not critical and small differences in cycle won't make huge difference. When I can't use a cyclestat (for infinite control of duration and frequency) I use the $20 digital timer by Intermatic, which let's you do something like 30-40 minutes on and 40 minutes off. Again, you want to use as little moisture as possible while still keeping the plants happy. You should be looking for that fine line between the root scar getting dried out and the level of moisture just above it. Just like the race car driver (or me) cannot know where the fine line is between speed and sliding out of control on a corner, without going over that line once, neither can you find the exact location of your line without drying one out. Not only does oxygen help plants grow fast, strong and big, but many people believe that if roots have to do a little searching for moisture they will grow bigger and faster.
-
02-11-2008, 01:09 AM #159Senior Member
Clone Log - Cloning with Pics using Master Kush mom...
hmm, A-, ok, i'll take that for the first attempt, thanks professor
really, small pump?
i figured using the 2 port and dedicating 1 stone to each would be good?:wtf:
ok, wrong stones? well, i saw your post about the bubble curtain after i bought and wet the stones, so, that kinda negated the idea of returning them.
I did run the thing, and although it took about 15-30 mins to get the lid all misty, it did eventually,, not supposed to get crazy soaked, right?
i dunno, if WH wants to try the bubble curtain, she sure can, and i'll never be insulted:thumbsup:
BTW-
speaking of clones,,,,,,,,,
I did something,,,,,,,,
someone might give me a odd look,,,,,,,,
I clipped a clone off of Galina last week.
she's just starting week 7, so i took the clipping in week 6.
its deserperation time folks!:wtf:
I just couldnt take all the stupid males that been sproutin all around me.:wtf:
I need a Mother.
so,
i took a low branch, very small flower on it and about 6 leaves.
in the morning i snipped off the flower while still on plant.
several hours later, (i allowed for some heal time) I clipped, scarified, hormone dipped, and stuck in a cup with very loose, lite soil, about 50% perlite and domed it.
its sitting in the veg bunker with the 4 sprouts.
been 2-3 days, so far, so good.
I will wait until there is intense root growth.
i sleeved a clear cup in a colored cup so i can check on root growth.
hopefully, this gives me a Blue Russian Mother.
I need a guaranteed fem if I'm gonna try this wet stuff you guys keep boggling my mind with.
I have decided to try a "waterfarm" single 4 gal drip unit, its about 50 bones complete.
I will add a bubbler to the bottom when I get it.
i'm sure i coulda made something, but decided this would be easier for the couple bucks I might save.
-
02-11-2008, 01:27 AM #160Senior Member
Clone Log - Cloning with Pics using Master Kush mom...
Originally Posted by Rock.Steady
Advertisements
Similar Threads
-
Organic Outdoor Flowering Puple, Master Kush, OG kush
By airdawg13 in forum Outdoor GrowingReplies: 6Last Post: 09-19-2010, 12:53 AM -
New Grow, Master Kush and Purple Kush
By dejayou30 in forum Grow LogReplies: 1Last Post: 12-15-2008, 09:48 AM -
HINDU KUSH VS. MASTER KUSH VS. OG KUSH
By dute12 in forum Basic GrowingReplies: 4Last Post: 05-01-2008, 02:44 AM -
cherry ak47-master kush- super kush-blueberry
By URACOTTONPICKER in forum Strains and SeedsReplies: 2Last Post: 07-22-2006, 05:13 PM -
master kush
By looselizzrd in forum Outdoor GrowingReplies: 0Last Post: 08-12-2004, 07:04 PM