Lightulb Vaporizer: How to...

[bobhasbitchtits]

This is a tutorial on how to construct and use a lightbulb vaporizer. It's a simple and easy to make contraption that will save you time and money and keeps the smell to a minimum, perfect for college dorms (my purpose).

Materials:

1. Lightbulb, any type, shape, size or brand, just make sure the lining (if it has a white lining) is powder, not the type that is painted on. Halogen bulbs also may pose a health risk.
2. 20 oz. plastic water bottle.
3. Straight pen body tube.
4. Pocket knife, scissors or other suitable cutting device.
5. Masking or duct tape.
6. Salt.
7. Lighter.
8. and of course: buds.


Construction:

1. First take your preferred lightbulb and cut around the small black plastic ring where the bulb makes contact with an electrical source when plugged in. Cut the metal, it is soft aluminum and is easily taken down by scissors or a knife.
2. Once the hole has been cut you can take this time to clean it up and make it look neat.
3. You will probably find a small glass cylinder sticking up from the bulb. This is where the argon was sealed into the bulb. This may be snapped off and will most likely break off without trouble. If it shatters, do not be alarmed, but break it into a garbage can just in case.
4. Now break away all the glass around the hole and make it as large as possible.
5. Now remove the filament and all wires and glass inside the bulb.
6. Now get salt and put about two table spoons inside the bulb. This will remove the powder lining and all impurities on the glass. Put one finger over the end of the bulb and swish the salt around to gather up the rest of the dust.
7. Now take the water bottle and cut off the top portion where it starts to taper into the top.
8. Then cut slits up towards the top of the bottletop all the way around the bottle then bend the slits inwards to make the opening smaller. You may need to trim the bottle according to your lightbulbs size and shape.
9. The cap of the bottle is the most important part of the device. First, cut a hole smaller than your pen body into one side of the top. A leather punch or screwdriver works well for this. Scissors are too big.
10. Make an indentical hole on the other side of the bottle top.
11. Choose one of the holes to be the carb and the other to hold the pen body. It doesn't matter really.
12. Back to the water bottle; place the slitted end over the top of the lightbulb and mold the bottle around it making as close a fit as you can. Put a few peices of masking tape over the seal as a preliminary fixture.
13. Once you've secured the top, tape all the way around it and make a permanent and airtight seal all the way around the top of the bulb and to the top of the bottle.
14. Now back to the bottle cap. Use your lighter to soften one of the holes and then force the pen body through the hole to make an airtight seal. If with this first try it is not airtight, then use some tape to make the seal.
15. Now screw the cap onto the water bottle top and you're set to go.

Use:
1. Grind up your bud and put about an eighth of a gram into the bulb. (This should suffice for one person, as the vapor is much more potent than the smoke).
2. Put the grinded bud into the bulb by taking off the cap and dropping it into the bulb.
3.. Cover both the holes, the stem and the carb, with your fingers as shown in the pic.
4. Flic your Bic and hold it close enough to the bulb, under the greens, but do not touch the flame to the bulb. If the bulb blackens then it's too close.
5. Once you see vapors start to swirl around the bulb then you can stop the heat, let it accumulate for about 10 seconds then release the carb and quickly suck all of the air out of the bulb.
6. Sit back and enjoy your new bulbvap and the smooth vapor-high. :thumbsup:

Pics in next post!

bobhasbitchtits Reviewed by bobhasbitchtits on 08-18-2007. Lightulb Vaporizer: How to... This is a tutorial on how to construct and use a lightbulb vaporizer. It's a simple and easy to make contraption that will save you time and money and keeps the smell to a minimum, perfect for college dorms (my purpose). Materials: 1. Lightbulb, any type, shape, size or brand, just make sure the lining (if it has a white lining) is powder, not the type that is painted on. Halogen bulbs also may pose a health risk. 2. 20 oz. plastic water bottle. 3. Straight pen body tube. 4. Pocket Rating: 5

[bobhasbitchtits]

First pics:

[bobhasbitchtits]

More pics:

[bobhasbitchtits]

Last pics:

[GosTo]

when u get tired of waiting so long to get high of the vape..

pour in some gasoline
(half full)
roll up a bounty paper towel
and stick it in the top
(make sure its pretty tight so gas cant leak out)
take it to the woods, or your asshole neighbors house
light the wick (paper towel)
and throw that sum bitch

[rmrdr716]

sticky this shit, very helpful

[budbomb420]

i use this all the time works great but use a candel

[GlassNBrass]

Marijuana Video: The Homemade Lightbulb Vaporizer Video

[MaryjaneAndHashley]

ive seen the video before, but your post made me wanna try it...its AWESOME!

[bobhasbitchtits]

Good stuff guys, thanks for the replies. If anyone else tries the vape, post your pics!