Am i soaking it in PH adjust water to 5.5 just like rockwool or is ther something more to it?
Printable View
Am i soaking it in PH adjust water to 5.5 just like rockwool or is ther something more to it?
Nope, but I just set mine to 6.0 and call it good.
After harvest, shake the HT out of the root balls as best you can before the root balls start to dry, rot, or otherwise disintegrate, and soak your HT in a tub of 6.0 water with some Cannazyme and an air stone for a week, mixing occasionally, then drain, rinse, and soak once more in fresh 6.0 water for a few more hours before use.
Darn stinky I just treated mine to a little bleach about a shot full in water for about a week drained resoaked couple hrs. plain old water seems to work for me. let dry and away we go.
Big Len
soaking right now in 6.0 adjusted tap water.
No airstone in the soaking tub.
How long should I be saoking for? 48 hours I figure would be safe...
(Brand new to hydro, running 8 bubblers)
until it consistently reads a ph of where you set it. Check and adjust often, hydroton WILL keep raising your ph over several hours.
I hate hydroton.
I recently pretreated hydrotron and I couldn't get a stable reading until I had it running in my system for a few days. Even with the presoaking and presoaking again.Quote:
Originally Posted by blink_inc
3 days of running it in the system and constantly staying on top of the PH adjustment has given me a PH that has been steady for at least 24 hours at a time now. Then again there's only 2 pots in my system right now. I'm about to put 4 more pots in there and add even more on Tuesday when the hydro shop opens and I can buy more pots/hydrotron.
You just pinned exactly why I hate hydroton. Never mind the coco puff effect.....the amount of time and energy wasted on 1) pretreating the crap FOREVER and 2) the amount of time you waste on plant growth for the first week or so until your h-ton FINALLY stabilizes. I had babies 2 and 3 weeks old that were growing slower than molassas in January due to a constantly unstable ph.Quote:
Originally Posted by daihashi
What is the coco puff effect?Quote:
Originally Posted by Weedhound
But yes I agree with what a PITA it is to get hydrotron dialed in. If I find it to be a hassle I'm going to build a pair of PH dosers for my 2 resevoirs to automatically adjust the PH for me. Hell I might do it anyway. It would allow me to be able to allow the plants to basically run on auto pilot for at least a week at a time.
The coco puff effect is twofold......the balls are very light and they are round.......drop your bucket and your plant is usually done for since there is absolutely NO stability to hydroton. It does not hold roots very securely imo and the fact that they roll everywhere (if you drop them) they are a complete PITA to deal with. Also becase of their airy nature they tend to "hold onto" extra nutes and salt allowing more overfert/salt buildup issues than I liked.
There are few pluses to hydroton....it's very light and seems to resist algae well but I NEVER reuse my media....no matter what it is......so the pros of h-ton come in WAY under the cons.
Hope this still falls under blink's q.......otherwise sorry for the threadjack.
Ahh.. I see, I went to hydrotron because it was a reusable medium. I bet after a few grows the hydrotron is probably stable from a long life sitting in hydro PH range; but I can definitely see the coco puff effect being an issue with pretty much no weight to hold the plant in place.Quote:
Originally Posted by Weedhound
It's definitely reusable (as are the higromite rocks I use) but the amount of work required to make sure your media is clean and disnifected is just too much trouble for me......I've tried it both with the hydroton and higromite.
I did not plan on reusing the media.
In fact, for the cost of 25$ for enough hydrotron to last at least 6 cycles, when I add in costs of airstones for each cycle I am still at less than $10 per cycle. When compared to soil, I was spending $50 per cycle on soil and perlite.
I have at least 2 weeks to pretreat so i will watch the PH level closely over the next few days and post back what goes on.
PH still sits at 6.0 after a few hours of soaking.
Interesting talk though. Thanks for chiming in..