Printable View
What i do when my bowl has a lot of resin is I heat up the bowl with a lighter, then use a paperclip to get out all of the resin. Then i roll all the resin back up into a ball and smooke it out of my piece. Resin is pretty ditry and tastes like shit, but if your dry...Its good to smoke. Then if you want to 100% clean your pipe place it in a mixture of rubbing alcohol and salt. That shit will lift all of the leftover resin right off the piece. It will look brand new.
really depends on the bowl u have...i use 2 dif. knifes,toothpick,an a cotton swab with the cotton off of it an the scrape forever lol...if u use a screen your resin will be more gooey an runny so you will need to let it dry a bit before u smoke it otherwise it will run right threw your bowl or clog your screen hardcore..an last but not least smoke small bits at a time if u try an smoke a whole lot at once the outside gets hard before the inside is done
depends on the pipe... with my small glass spoon i just use a paper clip, and go in through the carb hole.. it takes some thinking some times to figure out exactly how you're going to get the resin out. special ways? depends on the resin, if it's a hard crusty type (usually only see it in metal bowls) then all you gotta do is scrape it out and put it in your bowl, alot of times wtih my glass spoon i have this really really sticky-liqiudy resin, that you obviously have to add something to it to be able to smoke it. in this case, i either scrape up all the little tiniest bits of shake i can find, or ashes will work in a pinch, i refuse to mix tobacco and weed... for me, i get alot higher on resin then i do regular weed... but resin is the nastiest shit sometimes (sometimes it's just disgusting, and sometimes... it's just so fucking nasty, like if shit contained thc i'd rather eat shit then smoke the resin...) when i smoke resin it never quite all burns away, it'll get really fuckking hard like lava rock (if you've ever seen one) when it's at this point, best to just dump it out, there will always been something in your bowl unless you dump it/clean it out after smoking resin, but that doesn't mean it will even produce smoke anymore...
dude just do resin hits, its so much easier than scraping your pipe for resin, plus directly under the bowl hole is were alot of shake and partially burned weed is. ive gotten higher on like 3 resin hits than i did off of a bowl, because all that ash/shake/not quite all the way burned weed is super resinated YAY!
lol i just cleaned out my pipe and its alreay opaque again. when i cleaned it HUGE chunks of resin came out, like there must have been a tiny little air passageway (and its a huge glass spoon with large chamber)
i usually scrape my pipes after about an oz of usage... when i do clean mine out, it's not for a hit or two, or even a bowl.. when i go to clean out my bowl, i MUST know i'm getting high as fucking hell, or i won't do it all...
Tooth picks suck, boil your pipe or use your nails. Boiling the pipe then straining the ressin then drying it then smoking it then a cheap easy high that burns rather quickly.Quote:
Originally Posted by brave little toaster
I use a paper clip, bending it into a desired direction to get the most scrape. Then just I scrape whatever I get off onto a piece of paper and roll it into a ball when I'm done. Resin is super messy on the fingers, though. The best way is to mix it in with some weed. I've done it once and I got a badass case of the shakes for a little while. I realized it was just my vision shaking hahaha
Why does everyone boil there pipes, am i the only one here that uses the Rubbing alcohol and Salt technique to clean my piece?
Just wondering...?
No I use the alc/salt method. Boiling would give off a smell
If you do the rubbing alcohol/salt method, is there any way of keeping the resin to smoke, like you can with the boiling method?