ive got some ww clones i want to clone. and i want to do it aero ponically does any one have any advice on nutes cycles or other. mother was grown from seed beautiful growtth covered in crystals 1 weeks into flower
:rasta:
Printable View
ive got some ww clones i want to clone. and i want to do it aero ponically does any one have any advice on nutes cycles or other. mother was grown from seed beautiful growtth covered in crystals 1 weeks into flower
:rasta:
The major thing with clones is clean , clean , did I say clean. Everything , time exposed to air = seconds max.
Growing WW is easy if you use a simple rules , air movement and dark dark cycles. When it gets to the bud stage its so dense that its real easy to mold. MOLDIE pot is never used except for mulch in the garden. MOLD will kill you . So use lots of air movement in all directionis. If you do not use co2 injection use lots of fresh air.
Its a good Idea to use night cold air at the end of the cycle in bloom. I have used the 3 days of darkness and had good luck with it. For some straige reason it like it. Its a good producer and I feed flood and drain 1 hr after the lights on , once in the mid day, and 1 hour before the lights go out.
I have a average of .468 grams, per watt, per month over the years of growing.
Clean, Airflow, and you and your ww will be great. :thumbsup:
i need to know what are good nutes for aero system cloning. I found out the hard way its not quite the same as hydroplease some info soon
For aero-cloning you can use just straight water. Be sure to keep it warm, 70F-80F, or they won't root.Quote:
Originally Posted by phatsesh101
Alternately, Clonex makes a liquid solution that's designed for aero-cloners. I used that, with a bit of Hydroguard, on my last set of clones with good results.
I am trying the aero cloning and so far they all are living.
I used straight water, no hormones or nothing. No humidity dome either just water, air, and 30 watt fluorescent bulb. Yesterday I added a weak solution of superthrive to the reservoir to help promote roots.
This is my first try, in aero bubbler, I have really bad luck cloning.
Small roots have formed nothing spectacular, but none have died.
11 days into it.
Photos of the day I cut them and put into cloner and today.
Today also I am trying a fog cloner, I'll post how it works out.
ive yet to successfully clone anything only three times though once with aero but found full nutes didnt work and nethier do temps around 65 f for resevior
will clones grow on a indow seal even if the uv levels arent high. my other plant that i want to take the cutting of is doin fine.:smokebong::smokebong:
The temps. should be around 80 or better,for the nutes or water in your res. .. Add a aquarium heater and your well on your way to being the most successful cloner around. If your using soil for your cuttings,then you should add a heat mat under your tray.:thumbsup:Quote:
Originally Posted by phatsesh101
You should get a cfl or 2,and keep them under that on 24/7 light on cycle.They don't need inconsistant temps. Esspecially the roots. I found this out the hard way! I lost 3,due to low temps at root area.Quote:
Originally Posted by rostapharian
well its been about a week since i put some clones in peat, 9 of 13have roots thus far, some are coming through the peat when is it ok to transplant to soil and put into veg i took dome off yesterday for about an hour and they didnt look like they liked it to much. i just got my heater for my cloner and i want to use it already but i have got to wait for my clone lamp to finish the peat bound clones first. been growin from seed for 10 years outdoors but this inside stuff is fun. but im going to miss a pound per plant avg.