fireman
12-07-2006, 04:57 AM
Startin it up I want help form all the pros I been watching give me feedback the clock is ticking and I want this shit going.
PLEASE GIVE ME ALL THE FEEDBACK WANTED IF YOU HAVE ANY INFO ON ANY OF THE EQIUIPMENT, KNOW A GOOD METHODs( I LOVE DIY`S). ANYTHING I AM OPENED TO ANYTHING AND EVERYTHING AND LOVE TO OFFER AS MUCH HELP AS POSSIBLE IF I HAVE USED OR EXPERIECNED SOME THING IN THE SAME.
Well after compelting a full cycle to reap no fruits of my labor due to what I believe is bad karma possibly, I have decided to give it another grow this time bigger and a lot better. With all the knowledge I gained over the last 7 months from growing this beautiful plant I am addicted to growing it and b I must continue and see what I can do to its fullest. I have quite a bit of supplies, vast amounts of knowledge as I have read every book I believe, every message board, and just watched for months. Now i would like to join and offer what I have to share and definitely gain what everyone has to offer.
EQUIPMENT:I have gather a bit of equipment so I won`t be starting from scratch.
15 Buyducthcseeds.com seed White Widow, White Whito Rhine, and Skunk Special
465 EcoPlus fan
Can Filter of ebay
600 watt Sunsystem w/ Super Sun reflector
1000 Watt w/ 4`Cone reflector
T5- flourescent
EZ- Cloner (never used before any feedback will be much appreciated)
Future Equipment:
Seeds as necessary
Cool breeze 8`` reflector with 1000 watt light and ballast
8`` 740 Eco plus inline fan
When I add Co2:
Propane Gen
PPm3 controller
Area:
The room is 13`10``L x 10`7 1/2``W ( the front of the room is a little smaller In height due to ducting but I am using that as the cloning area)
I am going to be framing my room ,which is a basement made of brick,with 2x4 to seal it completely form the outside environment. I want it to be completely clean and optimal conditions when all up and running. I will either use drywall or panda-film to cover the framing havenā??t decided yet really depends on which one is cheaper but if panda film is much more effective I am will use that. (feedback welcomed) and havenā??t decided if I am going to insulate but probably wont again.
I will have a large area I want to divide into 3 separate areas Bloom, pre-bloom/veg, and clone. Any good ideas for dividing this area the door is on the front left and I will be building it so any size will work but have a pretty good idea unless better is presented.
Bloom area (7 feet Long x 10 feet Wide x 8 feet High)
I was thinking about using Soma`s soil beds but kinda going with my own version of 3x3 soil beds because I can fit around 5 comfortably into the break down for the bloom room I had. Possible just also 2 3x6 soil beds and a little area of 3x3 bed for hydro or another soil bed. Anyone know possible harvest with 2 3x6 beds sog style plants Prob around 30 plants in each bed ( 15 in 3x3 space)
Lights in the bloom area: I was thinking of 2 1000`s for now and eventually put them on movers so I can have an L shaped area with a middle section to walk in and then maybe cranking up more 1000`s to around 4 in the end. I would exaust these lights with the a 740 cfm that would get rid of the heat I believe.
Clone:
Right when you come in the room the clone area is on the right and it is going to be about 2 Ā½` feet long x 8` feet wide with tables in it and flouros over the ez-cloner
Pre bloom/Veg
It is 7 feet from the door to the bloom area wall that will separate the two rooms. To the left looking in from the door will just pretty much be my res and table space to work on and where I store nutrients and anything of the such. To the immediate right of the door will be the clone area I talked about.
Plan: Well I donā??t really know where to start cause I have so many ideas and want to do so much . I want to start a perpetual harvest (sog) and are pretty set on using soil ( soil beds)for a while with a little experimentation with hydro only for experience and itching my interest in it. Also this brings me to my first question. 1. Will I be able to implement CO2 and how so if Co2 at high levels stunts small plants growth?
I plan on the germing my 15 seeds in the next couple of weeks and starting on the framework to get everything going and start finding some mother plants. I am building everything the tables and all so if anyone has any ideas on my plans that think would be a good change let me know so I can think about it as well.
Hopefully when all up and running I will have 2 3x6 tables and one 3x3 table around 15 plants in each sog style hoping to yeild around 1oz to an 11/2 oz per plant if not more
So question s for people to answer are:
1.Will I be able to implement CO2 and how so if Co2 at high levels stunts small plants growth? Basically how do you setup a SOG with CO2?
2. Will I be able to yield around 2lbs per 3x6 area with a 1000w on a mover with around 15 plants per 3x3 area.
All I can think of for now an hav to get back to exams well all the people who love this forum as much as I do read up and let me know the way you do things.
PLEASE GIVE ME ALL THE FEEDBACK WANTED IF YOU HAVE ANY INFO ON ANY OF THE EQIUIPMENT, KNOW A GOOD METHODs( I LOVE DIY`S). ANYTHING I AM OPENED TO ANYTHING AND EVERYTHING AND LOVE TO OFFER AS MUCH HELP AS POSSIBLE IF I HAVE USED OR EXPERIECNED SOME THING IN THE SAME.
Well after compelting a full cycle to reap no fruits of my labor due to what I believe is bad karma possibly, I have decided to give it another grow this time bigger and a lot better. With all the knowledge I gained over the last 7 months from growing this beautiful plant I am addicted to growing it and b I must continue and see what I can do to its fullest. I have quite a bit of supplies, vast amounts of knowledge as I have read every book I believe, every message board, and just watched for months. Now i would like to join and offer what I have to share and definitely gain what everyone has to offer.
EQUIPMENT:I have gather a bit of equipment so I won`t be starting from scratch.
15 Buyducthcseeds.com seed White Widow, White Whito Rhine, and Skunk Special
465 EcoPlus fan
Can Filter of ebay
600 watt Sunsystem w/ Super Sun reflector
1000 Watt w/ 4`Cone reflector
T5- flourescent
EZ- Cloner (never used before any feedback will be much appreciated)
Future Equipment:
Seeds as necessary
Cool breeze 8`` reflector with 1000 watt light and ballast
8`` 740 Eco plus inline fan
When I add Co2:
Propane Gen
PPm3 controller
Area:
The room is 13`10``L x 10`7 1/2``W ( the front of the room is a little smaller In height due to ducting but I am using that as the cloning area)
I am going to be framing my room ,which is a basement made of brick,with 2x4 to seal it completely form the outside environment. I want it to be completely clean and optimal conditions when all up and running. I will either use drywall or panda-film to cover the framing havenā??t decided yet really depends on which one is cheaper but if panda film is much more effective I am will use that. (feedback welcomed) and havenā??t decided if I am going to insulate but probably wont again.
I will have a large area I want to divide into 3 separate areas Bloom, pre-bloom/veg, and clone. Any good ideas for dividing this area the door is on the front left and I will be building it so any size will work but have a pretty good idea unless better is presented.
Bloom area (7 feet Long x 10 feet Wide x 8 feet High)
I was thinking about using Soma`s soil beds but kinda going with my own version of 3x3 soil beds because I can fit around 5 comfortably into the break down for the bloom room I had. Possible just also 2 3x6 soil beds and a little area of 3x3 bed for hydro or another soil bed. Anyone know possible harvest with 2 3x6 beds sog style plants Prob around 30 plants in each bed ( 15 in 3x3 space)
Lights in the bloom area: I was thinking of 2 1000`s for now and eventually put them on movers so I can have an L shaped area with a middle section to walk in and then maybe cranking up more 1000`s to around 4 in the end. I would exaust these lights with the a 740 cfm that would get rid of the heat I believe.
Clone:
Right when you come in the room the clone area is on the right and it is going to be about 2 Ā½` feet long x 8` feet wide with tables in it and flouros over the ez-cloner
Pre bloom/Veg
It is 7 feet from the door to the bloom area wall that will separate the two rooms. To the left looking in from the door will just pretty much be my res and table space to work on and where I store nutrients and anything of the such. To the immediate right of the door will be the clone area I talked about.
Plan: Well I donā??t really know where to start cause I have so many ideas and want to do so much . I want to start a perpetual harvest (sog) and are pretty set on using soil ( soil beds)for a while with a little experimentation with hydro only for experience and itching my interest in it. Also this brings me to my first question. 1. Will I be able to implement CO2 and how so if Co2 at high levels stunts small plants growth?
I plan on the germing my 15 seeds in the next couple of weeks and starting on the framework to get everything going and start finding some mother plants. I am building everything the tables and all so if anyone has any ideas on my plans that think would be a good change let me know so I can think about it as well.
Hopefully when all up and running I will have 2 3x6 tables and one 3x3 table around 15 plants in each sog style hoping to yeild around 1oz to an 11/2 oz per plant if not more
So question s for people to answer are:
1.Will I be able to implement CO2 and how so if Co2 at high levels stunts small plants growth? Basically how do you setup a SOG with CO2?
2. Will I be able to yield around 2lbs per 3x6 area with a 1000w on a mover with around 15 plants per 3x3 area.
All I can think of for now an hav to get back to exams well all the people who love this forum as much as I do read up and let me know the way you do things.