PDA

View Full Version : I wanna make a bong outta this


jacquelyne
03-11-2005, 01:56 AM
Its a Black sambucca bottle.
really thick black glass
its 45cm or 17 1/2 inches long
I need to know how i go about drilling through the glass.I think i need a special diamond tipped drill bit is that right?Also i think a normal drill wont go through that glass (even with a diamond tipped drill bit) as it would bounce around everywhere and probably chip it.Do i need a drill press?I have everyhing else i need i just need some advice to get the best neatest hole.I can always sand it if its a bit rough.Hole has to be 15mm or 1 1/2 inch in diameter.Can u get diamond tips that wide ? im sure it would be possible.Any ideas or suggestions would be great please.
Dick Justice
03-11-2005, 02:24 AM
I've seen a product that just attaches to the top of a bottle, and boom, instant bong. If you don't have the expensive drill equipment, maybe that's the way to go?
jacquelyne
03-11-2005, 02:49 AM
What is it?
Do you know where i can get a pic so i can understand how it works as ive never seen nothing like that.What about a shotty u know the little hole at the back or theres none ? Ive smoked bongs with no shotty i need one on there but the thing your saying might have one on the part.
Dick Justice
03-11-2005, 02:51 AM
Found it. (http://shop.grasscity.com/shop/grasscity/MISP213.html)

Price is a bit steep, but it's still cheaper than buying diamond drill bits.
vapoorize
03-11-2005, 02:56 AM
Here's how I make vaporizers and bongs. Take a cap that fits it (or anything that will plug the top) find a straw that fits to the bottom. Drill or poke 2 holes in the cap. Attach your bowl to the straw, seal it with playdough, and insulate it with foil so that it won't melt the straw around it. Take a straw or some sort of tube and put it in another hole in the "cap". you can now unscrew it and fill with water. Stick it back in, light up the bowl, and suck through the other straw. I find it looks food too!
jacquelyne
03-11-2005, 03:06 AM
They are cheaper than the thing you showed me lol.Im still a bit confused as all use is a bong a normal bong with a mouth hole , a stem with cone and a shotty.Thats what i really would like to make.I can out of plastic very easily its just the whole glass drilling thing.Thank you so much for the pic.URL=http://shop.grasscity.com/shop/grasscity/MISP213.html]Found it.[/URL]

Price is a bit steep, but it's still cheaper than buying diamond drill bits.[/QUOTE]
slipknotpsycho
03-11-2005, 05:21 AM
you can buy a set of bits from walmart for like 10 bucks....glass drilling ones i mean.
Encatuse
03-11-2005, 07:14 AM
http://everyonedoesit.com/online_headshop/Bottle_Bong_adaptor__One_piece.cfm?iProductID=648&iProductCategoryID=155

There. It's Poi-fect, no? And if it doesnt fit the bottle you can either shave the rubber or add duct tape as needed.
F L E S H
03-11-2005, 05:59 PM
Encatuse, I have one exactly the same as that, except it has 3 tubes... :D
Natural Vibrations
03-11-2005, 07:54 PM
Encatuse is a pimp
jacquelyne
03-11-2005, 09:24 PM
http://everyonedoesit.com/online_headshop/Bottle_Bong_adaptor__One_piece.cfm?iProductID=648&iProductCategoryID=155

There. It's Poi-fect, no? And if it doesnt fit the bottle you can either shave the rubber or add duct tape as needed.
So that thing at the top is the cone ?
And the thinner hose hmmm
Is that where air comes out ?